Connect the Macard extender to a power outlet located near your router. Wait until the Power LED turns solid.
Find the WPS button and press it.
This means that the WPS light should begin blinking. The WPS light on the router should start blinking.
Press the WPS button of your Macard extender within 2 minutes after pressing the WPS button of the router.
The WPS light should start blinking on the extender.
The extender should be solid after about 30-60 second, indicating that the connection was successful. You can move the device anywhere within range of your router after the connection.
Via Gomacard.online
Connect the Macard extender to a power outlet close to your router. Wait until the LED becomes stable (this could take a few minutes).
Go to WiFi settings on your computer, tablet or phone.
Connect to the network by searching for its name. There may not be a password required.
Go to gomacard.online in your browser. Log in to the device using the default admin credentials.
Login with the default password
Username : admin
Password : admin
Select "Repeater Mode" from the menu. The app will search for WiFi networks nearby.
Choose your primary WiFi network. Enter the WiFi password for your router.
You can choose to name your extended network or leave it at the default.
Via the 192.168.10.1
Macard WiFi extender should be placed in the middle of your wireless router, and the area you wish to extend Wi-Fi. Connect it to a power outlet, then connect to its WiFi network.
Go to the WiFi settings to connect your computer. The manual of the extender will usually mention this network name (SSID). This initial connection is unlikely to require a password.
Open any browser on the connected device.
Enter 192.168.10.1 into the address bar.
Now you should see the login page for your Macard wifi extender.
Often, the default username and password for both fields is admin.
Click Login and enter your credentials.
A setup wizard will guide you once you log in. Follow the instructions on screen.
Search for Wi-Fi networks nearby. Select the name (SSID), of your home Wi-Fi network.
Enter the password to your home Wi-Fi.
You may be asked to create a new Wi-Fi extended network name (SSID).
You can keep the name of your main network, or you can create a different one so that the extended network is easily identifiable.
When you click Save, the extender will attempt to connect to an existing Wi-Fi network to broadcast your extended network.
Where Should the Extender Be Relocated After Installation?
Connect your device to the newly extended WiFi network by disconnecting it from the setup WiFi network. Use the password that you entered when configuring the extender. To relocate the extender to another location, make sure it is within the range of the main router.
Troubleshooting tips
Rebooting Extender Network
Remove the extension cord from the outlet. Unplug the extender for 15-30 seconds. It will then shut down completely. Reconnect the device to the outlet.
Wait a few moments for the extender's power to come back on, re-establish a connection with your router main and broadcast its expanded network. You will typically see the indicators lights cycle, and then return to their normal state.
Resetting Macard WiFi Extender
Make sure that your Macard WiFi extender has been plugged in and turned on.
Use a paperclip or an object with a thin, pointed tip. Insert the paperclip gently into the reset pinhole. Hold the reset button down for 8-10 seconds. Release the reset button after 8-10 seconds.
Now, the extender will reboot by itself. It may take a couple of minutes for this process to complete. When the indicator lights return to their default settings, you'll know that it's done.
The Summary
It is easy to set up the MACARD RE1200 wifi extender by using IP address or WPS. You have hopefully chosen the correct setup method and installed the device successfully.
FAQs
How do I set up Macard model RE1200 WiFi extender?
Install the device using WPS, IP address or interface. The blog post contains all the instructions for each setup method.
How do I change the password on Macard RE1200 Wireless Extender?
Use the IP or URL address to access the interface of the extender. Select Wireless Settings in the settings. Enter the new WiFi password after selecting SSID. Apply it by saving.
0 Comments